Welcome to HardwareForumz.com!
FAQFAQ    SearchSearch      ProfileProfile    Private MessagesPrivate Messages   Log inLog in

PM4-915G/PD1 help needed

 
   Hardware Problem Solving Community! (Home) -> FIC RSS
Next:  Reburbished drive is BETTER than the NEW ONE?? wt..  
Author Message
garybrockie1

External


Since: Jul 26, 2007
Posts: 1



(Msg. 1) Posted: Thu Jul 26, 2007 5:57 pm
Post subject: PM4-915G/PD1 help needed
Archived from groups: alt>comp>periphs>mainboard>fic (more info?)

Hi, I have a Tiny 5-3500 PCI Express and have put it into a new case.
The problem I have is that I am left with a grey wire that has 8 small
wires coming from it with small single push connectorsand I dont know
were they go. They are labled:
Mic-in
Mic-power
L-out
L-ret
R-out
R-ret
2x Ground
There is also a red and black wire with a double pin connector that
says Speaker.
I would be most gratefull for any help.

 >> Stay informed about: PM4-915G/PD1 help needed 
Back to top
Login to vote
Alex Zorrilla

External


Since: May 14, 2004
Posts: 181



(Msg. 2) Posted: Fri Aug 17, 2007 9:55 pm
Post subject: Re: PM4-915G/PD1 help needed [Login to view extended thread Info.]
Archived from groups: per prev. post (more info?)

If I had to guess off the top of my head, the first connector sounds
like a front panel audio header. If your new case has speaker and
microphone connections at the front, that is what this connector is for.
Look for something on the motherboard that says "Front Panel Audio".

The second connector sounds like it is for the computer speaker that
goes "beeeeeep!" Typically, this connection is in the same bank of
connectors as all the other front panel connections (power switch, reset
button, power LED, hard drive LED, etc.). If it is not in the same
bank, then it is probably somewhere near it.

Hope this helps.

--Alex



G@ZZ@ wrote:
> Hi, I have a Tiny 5-3500 PCI Express and have put it into a new case.
> The problem I have is that I am left with a grey wire that has 8 small
> wires coming from it with small single push connectorsand I dont know
> were they go. They are labled:
> Mic-in
> Mic-power
> L-out
> L-ret
> R-out
> R-ret
> 2x Ground
> There is also a red and black wire with a double pin connector that
> says Speaker.
> I would be most gratefull for any help.
>

 >> Stay informed about: PM4-915G/PD1 help needed 
Back to top
Login to vote
Display posts from previous:   
Related Topics:
P4M-915G/PD1 Mainboard - Anyone know what the on board sound card is on one of these boards. The Manual says it`s a Grantsdale Dynasty Mainboard P4M-915G/PD1 Thanx in advance

KA-6130 Drivers needed -

KA-6130 drivers needed -

PA-2013 VIA 4in1 drivers needed for PCI display? - I have a spare computer with PA-2013 Rev. 2 E-O036 MB and want to use a PCI Diamond Viper V330 display card. I know that I use the 4in1 drivers for AGP, but are they needed for PCI display card? If so, do I use all of them, excluding the AGP driver?..

Game port plug needed for FIC AN19C - I have the AN19C mainboard with onboard sound. This mainboard doesn't have the game/midi port onboard. I have to get game port cable that plugs into the mainboard's game port connector pins. Does anyone know of a vendor that sells these?
   Hardware Problem Solving Community! (Home) -> FIC All times are: Pacific Time (US & Canada)
Page 1 of 1

 
You can post new topics in this forum
You can reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum



[ Contact us | Terms of Service/Privacy Policy ]